Jump to content
Potato

Zoom2 power

Recommended Posts

(Zoom2) - (Zoom) required!

Add a 2nd image/gif when zoomed in!

 

Basically you can use 2 images. One will show normally (30x30) but when someone zooms in on your avatar it will show your 2nd image (80x80).

 

Example of where it would come in handy is to have a 3d gif as 80x80 like most people have them as your zoom2 image then crop it to 30x30 to use as normal image. Because a 80x80 image shrunk down by xat can look a bit pixely and weird (Not exactly sure how to describe it).

 

It can also be used in different ways for example. You can have your 30x30 normal image as a picture of a gift box but when people put their mouse over it your zoom2 image would be whatever was in the gift box! :p

 

 

Hope I did a good job of describing it. I would make an example but my internet is down :( -on 4g mobile-

Edited by Potato
  • Award 1

Share this post


Link to post
Share on other sites

So how would (zoom) and (zoom2) interact? 

 

Would users no longer be able to use the orignal zoom power to see a user’s first picture? 

 

I’m not sure I like this idea.. not yet, anyway. 

Share this post


Link to post
Share on other sites
4 minutes ago, Angelo said:

So how would (zoom) and (zoom2) interact? 

 

Would users no longer be able to use the orignal zoom power to see a user’s first picture? 

 

I’m not sure I like this idea.. not yet, anyway. 

Glad you asked. If you don't use a 2nd image zoom will work normally

 

A zoom2 code for example could be:

 

IMGURL1#IMGURL2

 

If avatar code is only IMGURL1 it will zoom in normally as it does now

Share this post


Link to post
Share on other sites
On 5/27/2018 at 12:09 AM, Potato said:

Glad you asked. If you don't use a 2nd image zoom will work normally

 

A zoom2 code for example could be:

IMGURL1#IMGURL2

what about pcback and pcbr (tired)

Share this post


Link to post
Share on other sites
1 hour ago, Devil said:

what about pcback and pcbr (tired)

Didn't think about that, thank you. The code could be:

 

IMGURL1<z2>IMGURL2#pcgback

Share this post


Link to post
Share on other sites
2 hours ago, Potato said:

Didn't think about that, thank you. The code could be:

 

IMGURL1<z2>IMGURL2#pcgback

You can clearly see now this would get pretty messy pretty quick. 

 

On 5/27/2018 at 2:09 AM, Potato said:

Glad you asked. If you don't use a 2nd image zoom will work normally

 

A zoom2 code for example could be:

 

IMGURL1#IMGURL2

 

If avatar code is only IMGURL1 it will zoom in normally as it does now

Not to mention that I still think if you’re using both (zoom) and (zoom2) with two images, it seems like you’d be unable to zoom into the first image. 

Share this post


Link to post
Share on other sites
8 hours ago, Angelo said:

You can clearly see now this would get pretty messy pretty quick. 

Namegrad and namewave seemed messy and confusing too at first but was easy to get used to.

8 hours ago, Angelo said:

Not to mention that I still think if you’re using both (zoom) and (zoom2) with two images, it seems like you’d be unable to zoom into the first image. 

The point of the power is to replace the zoomed image with a 2nd image.

Share this post


Link to post
Share on other sites

I understand your idea and i support it. In the past months i noticed that pixely and weird issue in high definition or bigger images. Also, it would be best fit as a boost on zoom power.

Share this post


Link to post
Share on other sites

 

On 5/30/2018 at 9:02 AM, Potato said:

 

The point of the power is to replace the zoomed image with a 2nd image.

 

On 5/27/2018 at 9:09 AM, Potato said:

A zoom2 code for example could be:

 

IMGURL1#IMGURL2

 

If avatar code is only IMGURL1 it will zoom in normally as it does now

I'm not sure if I'm getting this correctly, buy since you can put the image links the way like this ''IMGURL1#IMGURL2'', does the image link2 have to be the same as the image link1? If not, wont it actually be possible that a user can put a different image from image link1?

 

2 hours ago, Stif said:

I understand your idea and i support it. In the past months i noticed that pixely and weird issue in high definition or bigger images. Also, it would be best fit as a boost on zoom power.

I's agree if this idea would be a boost to the Zoom power. 

 

Share this post


Link to post
Share on other sites
Guest

The idea seems good but instead of make a second power i think we could just boost the old one.

Share this post


Link to post
Share on other sites
On 6/1/2018 at 10:18 PM, 6 said:

 

 

I'm not sure if I'm getting this correctly, buy since you can put the image links the way like this ''IMGURL1#IMGURL2'', does the image link2 have to be the same as the image link1? If not, wont it actually be possible that a user can put a different image from image link1?

 

I's agree if this idea would be a boost to the Zoom power. 

 

Could be a boost or a power. I would just like the feature added.

 

If you put just 1 image zoom will work as it does now. If you add a 2nd image then the 2nd image will appear as the 80x80 image when the smaller 30x30 image is hovered over. I'll work on an image example. Give me a few

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.